Florence 14mm Engineered Oak Flooring Installation Guide

Engineered floors are very dimensionally stable allowing them to be installed over most types of sub floors. They are suitable for all areas of the house except bathrooms and wet areas. They are also suitable for use over underfloor heating. Florence 14mm Engineered Oak Flooring can be installed as either a floating floor.

Tongue & Groove Floating Installation

Floating Installation is the most common and DIY friendly installation method because it is the easiest and the fastest to do, can be installed over any type of subfloor and it does not require any special skills or prior experience in installing floors. Tongue & groove floors are fixed together by running a bead of PVA glue down the groove and knocking into the tongue of the next board.

All flooring installations must use an approved underlay. Over a concrete subfloor you will need to use and underlay which has a built in damp proof membrane like Barrier Plus, while over a wooden subfloor you can use the standard Barrier underlay. For installations over underfloor heating we recommend using Tuplex underlay.

You will need to leave a 10mm expansion gap around the perimeter of the room. To maintain this gap during installation spacers are provided in the installation kits (purchased separately). After you have installed the floor you can cover this expansion gap with scotia / beading or new skirting boards The 10mm expansion gap also needs to be left in doorways where the floor follows through from one room to another; we have a full range of door profiles available to match your floor.

The above is a brief guideline on the installation of engineered flooring, always refer to the manufactures installation guidelines contained within packs of the flooring.

Download Florence Floating Installation Guide

If you require any further advice on installation the please call our technical department on 0845 263 6586 or e-mail us on info@ukflooringdirect.co.uk or click the Live Help Button at the top of the page.

Maintenance Guide For UV Oiled Floors

In order to ensure lasting satisfaction from your new UV oil finished floor, it is important to correctly care for the floor starting immediately after installation. With the right care, the oiled floor will become increasingly easy to clean and more hard wearing over time. This is because the recommended soap used to clean the floor actually coats it with an invisible film, providing additional protection and thus making the floor more resistant to dirt. As well, the floor can be re-oiled as part of a regular maintenance program thus ensuring a lifetime of use and enjoyment.

After-Installation Care

All UV Oiled floors are recommended to be finished with WOCA Maintenance Paste right after installation and before the floor is used. As a result of this the surface will then be more hardwearing and be easier to clean and maintain in the future.

Normal Basic Cleaning

Normal cleaning to remove surface debris is accomplished using a broom or vacuum cleaner. To remove normal stains and non-loose dirt, the floor should be cleaned with water and a hard-wrung, wet cloth. In order to achieve the best cleaning possible use WOCA Natural Soap Cleaner. This soap is added to the water in a 40:1 solution. WOCA Natural Soap has two functions: it cleans the floor and at the same time forms an invisible, protective film on the surface of the floor making it even more resistant to damage from dirt. It is very important to use two buckets when cleaning the floor- one with the WOCA Natural Soap mixed solution and one with clean water for rinsing the dirty cloth or mop. Immerse the cloth or soft mop in the Soap solution, and then wring out the excess fluid before wiping the floor. Rinse the cloth or mop in the clear water, wring out the excess water, then immerse in the Soap solution again. Repeat this pattern until the floor is clean. Do not pour the Soap solution directly on the floor but instead, always use a cloth or mop to apply the solution.

Cleaning Extremely Dirty Floors

If the floor has been neglected and/or becomes very dirty, it should be cleaned using WOCA Intensive Wood Cleaner. This is added to water in a 40:1 ratio, following the guidelines above. Immediately after cleaning with the Intensive Cleaner, the floor should then be cleaned with WOCA Natural Soap (as above) in order to restore the protective soap film then finished with WOCA maintenance Paste.

Spot Remover

Difficult spots can be removed with WOCA Spot Remover. The Spot Remover is sprayed on the spot and left in place until the stain is dissolved, repeat treatment if necessary. The area is then cleaned and re-oiled with WOCA Maintenance Paste.

We recommend that you purchase a WOCA UV Oiled Maintance Kit with your floor.

Each kit contains

1.0 liter Natural Soap Concentrate (Will cover 350m2)
1.0 liter Intensive Wood Cleaner (Will cover 200m2)
400ml Maintenance Paste (Will cover 100m2)
1 Polishing Pad and 1 Cloth.