City Metropolitan European Family Oak 130mm Brushed & Oiled Flooring is 130mm wide, has a total thickness of 14mm and comes in standard lengths of 2200mm. The floor has a 2.5mm hardwood layer which if need can be sanded and re-finished up to 3 times, but under a normal maintenance program and in a domestic environment the floor should not need to be sanded for around 20 years.

This is a 3 ply engineered floor so it is made from 3 different layers, one being the hardwood wear layer with the other 2 being constructed from spruce. Each of the planks has bevelled edges (V Grooves) on all four sides resulting in very distinctive groove between the planks, adding more depth and dimension along with giving an individual definition to each plank.

The family grade of this hardwood shows the true excellent appearance of the wood, the pattern of the rings beautifully depicts the annual growth of the tree and while small knots, limited character marks are allowed there is little or no sapwood, mineral streaks or splits. Before applying the finish, the surface of the wood is roller brushed to remove some of the softer summer growth rings from the grain; this gives a naturally textured surface that gently highlights the natural grain structure.

The floor is then prefinished with oil which adds a deep warm natural feel to the floor. This seemingly transparent surface enhances the natural grain and structure of the wood, allowing its natural beauty to show whilst still offering a deep protection.

City Metropolitan European Family Oak 130mm Brushed & Oiled Flooring Installation Guide

Engineered floors are very dimensionally stable allowing them to be installed over most types of sub floors. They are suitable for all areas of the house except bathrooms and wet areas. They are also suitable for use over under floor heating. Due to their stability they only need acclimatising for 48 hours, to correctly acclimatise your engineered floor it should be left in the room it is going to be fitted in at normal room temperature.

%name% has a click installation system and can be installed as a floating floor which is the most common and DIY friendly installation method because it is the easiest and the fastest to do, can be installed over any type of subfloor and it does not require any special skills or prior experience in installing floors as the floors just clicks together with no need for any glue.

All floating flooring installations must use an approved underlay. Over a concrete subfloor you will need to use a underlay which has a built in vapour barrier like Cushion Plus White Underlay, while over a wooden subfloor you can use the Cushion Standard White Underlay. For installations over under floor heating we recommend using Cushion Heat Flow underlay. Superior underlays like Cushion Ultra Silver Underlay and Cushion Premium Black Underlay can be used to give better support to your new flooring which prolongs the life and also aids during installation by removing some minor imperfections from the sub-floor. Also for improved noise reduction we recommend the Cushion Acoustic Pro Underlay, bringing peace and quiet to the room.

Each board has a click profile on all four sides to join the boards together simply insert the tongue into the groove at a high angle and then push the board down; the boards will then click together.

You will need to leave a 10mm expansion gap around the perimeter of the room. To maintain this gap during installation spacers are provided in the installation kits (purchased separately).

After you have installed the floor you can cover this expansion gap with scotia / beading or you can replace you old skirting boards with new ones, this gives a much more professional finish. The 10mm expansion gap also needs to be left in doorways where the floor follows through from one room to another; we have a full range of door profiles available to match your floor.

The above is a brief guideline on the installation of engineered flooring; always refer to the manufactures installation guidelines contained within packs of the flooring or visit out Flooring Manufacture Installation Guides

If you require any further advice on installation then please call our technical department on 0845 263 6586, e-mail us on info@ukflooringdirect.co.uk or click the Live Help Button at the top of the page.

City Metropolitan European Family Oak 130mm Brushed & Oiled Flooring Maintenance Flooring Guide

 In order to ensure lasting satisfaction from your new oil finished floor, it is important to correctly care for the floor from the off, starting immediately after installation. With the right care, the oiled floor will become increasingly easy to clean and more hard wearing over time. This is because the recommended soap used to clean the floor, actually coats it with an invisible film, providing additional protection and thus making the floor more resistant to dirt. The floor can also be re-oiled as part of a regular maintenance program thus ensuring a lifetime of use and enjoyment.

After-Installation Care

All oiled floors are recommended to be thoroughly cleaned with “Easy Clean Oiled Flooring Natural Soap Cleaner” right after installation and as a regular cleaning regime.  As a result of this the surface will then be more hardwearing and be easier to clean and maintain in the future.

Normal cleaning to remove surface debris is accomplished using a broom and vacuum cleaner. In order to achieve the best cleaning possible use, “Easy Clean Oiled Flooring Natural Soap Cleaner” a highly concentrated soap for cleaning and maintenance of oiled wooden surfaces, suitable for flooring, furniture, kitchen surfaces, and all indoor wood.

 Instruction for use:

1. Shake thoroughly prior to use.

2. Always use two buckets: one – for the soap solution, the other – water for rinsing.

3. Mix approx. 250ml of the soap with 10L of warm water and apply a thin layer onto the flooring; particularly soiled areas should be cleaned with a brush or cloth first.

4. Rinse the cloth or mop in the second bucket and wipe the floor dry.

5. Water in the other bucket should be changed regularly so as to prevent spreading the already removed dirt back onto the floor.

6. Do not wipe the floor with pure water as the protective soya and coconut oils will be removed!

7. With each subsequent use of the soap, the floor will become less susceptible to soiling.

Coverage approx. 50-80 m2/l, Dependent on wood type.

Cleaning Extremely Dirty Floors

If the floor has been neglected and/or becomes very dirty, it should be cleaned using “Easy Clean Oiled Flooring Intensive Cleaner,” developed for deep penetration of the woods fibre, helping to lift the grain and encourage absorption of a new application of “Easy Clean Oiled Flooring Refresher.” 

Instructions for use 

1. Shake thoroughly prior to use.

2. Always use two buckets: one – for the soap solution, the other – water for rinsing.

3. Mix approx. 250ml of the soap with 10L of warm water and apply a thin layer onto the flooring; particularly soiled areas should be cleaned with a brush or cloth first.

4. Rinse the cloth or mop in the second bucket and wipe the floor dry.

5. Water in the other bucket should be changed regularly so as to prevent spreading the already removed dirt back onto the floor.

6. Do not wipe the floor with pure water as the protective soya and coconut oils will be removed!

7. With each subsequent use of the soap, the floor will become less susceptible to soiling.

Coverage approx. 50-80 m2/l, Dependent on wood type.

Maintenance Oil Application

“Easy Clean Oiled Flooring Refresher,” for use on all oiled wooden surfaces. 

Used once or twice a year, depending on the level of dirt, to restore and protect, if the floor has become dull and tired looking. It will help in everyday care and reinforces the floors resistance to dirt, and help to give it a new lease of life.

Instruction for use:

1. First clean the soiled surface with “Easy Clean Oiled Flooring Intensive Cleaner,” and leave to dry thoroughly for 4 to 8 hrs.

2. Apply a thin layer of “Easy Clean Oiled Flooring Refresher,” with a diffuser or a cloth and then rub manually or mechanically into the wood with a polishing machine until a smooth, silky-matt surface is revealed.

3. Make sure you leave no excess oil on the surface.

4. Within approx. 4 hrs. The floor may be walked on, though the full hardening time is 24 hrs. During which time the floor must not be cleaned with water and should be used sparingly and with care.

5. For future after care and routine cleaning  maintenance “Easy Clean Oiled Flooring Natural Soap Cleaner,” is then recommended.

6. Easy Clean Oiled Flooring Refresher is ready-to-use without diluting

Coverage approx. 50-60 m2/l, Dependent on the wood type.

All the products related to maintaining this flooring will be available to purchase at very competitive prices after you have selected your flooring and added to the basket.

If this does not answer all of your questions or you wish for some further advise please do not hesitate to contact us.