Click System Engineered Flooring

Engineered floors are very dimensionally stable allowing them to be installed over most types of sub floors. They are suitable for all areas of the house except bathrooms and wet areas. They are also suitable for use over underfloor heating. Click System Engineered floors are installed as a floating floor.

Click System Floating Installation

Click System Floating Installation is the most common and DIY friendly installation method because it is the easiest and the fastest to do, can be installed over any type of subfloor and it does not require any special skills or prior experience in installing floors as the floors just clicks together with no need for any glue.

All flooring installations must use an approved underlay. Over a concrete subfloor you will need to use and underlay which has a built in damp proof membrane like Barrier Plus, while over a wooden subfloor you can use the standard Barrier underlay. For installations over underfloor heating we recommend using Tuplex underlay.

Each board has a click profile on all four sides to join the boards together simply insert the tongue into the groove at a high angle and then push them down. The boards will then click together.

To allow for any movement of the floor you will need to leave a 10mm expansion gap around the perimeter of the room. To maintain this gap during installation spacers are provided in the installation kits (purchased seperately). After you have installed the floor you can cover this expansion gap with scotia / beading or new skirting boards. The 10mm expansion gap also needs to be left in doorways where the floor follows through from one room to another; we have a full range of door profiles available to match your floor.

The above is a brief guideline on the installation of solid wood flooring, always refer to the manufactures installation guidelines contained within packs of floor. View Manufactures Installation Guides.

ATTENTION – INSTALLER/OWNER RESPONSIBILITY

Inspect all materials carefully before installation. Wood is a natural product containing variations in colour, tone and graining. Some variation in colour is to be expected in a natural wood floor. Beautiful hardwood floors are a product of nature and therefore not perfect. These floors are manufactured in accordance with accepted industry standards, which permit a defect tolerance of 5%. Even though our product goes through many inspections before it leaves the plant, it is the responsibility of the customer and installer to perform a final inspection prior to installation. Any warranties offered with this product do not cover materials with visible defects once the product is installed.

JOB SITE CONDITIONS

It is the responsibility of the owner/installer to determine if the jobsite sub-floor and job site conditions are environmentally and structurally acceptable for wood floor installation. The installer/owner is responsible for wood failure resulting from or connected with sub-floor, subsurface, job site damage, deficiencies or using inadequate accessories after the hardwood flooring has been installed.

PLEASE NOTE:

Always read the full manufactures recommended installation guides before installation which you will find in every 3rd pack of flooring.

Maintenance Guide For Lacquered Floors

In order to ensure lasting satisfaction from your new lacquered floor, it is important to correctly care for the floor starting immediately after installation. With the right care, the lacquered floor will become increasingly easy to clean and more hard wearing over time. This is because the recommended soap used to clean the floor actually coats it with an invisible film, providing additional protection and thus making the floor more resistant to dirt.

After-Installation Care

All lacquered floors are recommended to be cleaned with WOCA Lacquer Soap right after installation and before the floor is used. As a result of this the surface will then be more hardwearing and be easier to clean and maintain in the future.

Normal Basic Cleaning

Normal cleaning to remove surface debris is accomplished using a broom or vacuum cleaner. To remove normal stains and non-loose dirt, the floor should be cleaned with water and a hard-wrung, wet cloth. In order to achieve the best cleaning possible use WOCA Wood Cleaner, which is mixed with water at a ratio of 40:1. This has two functions: it cleans the floor and at the same time forms an invisible, protective film on the surface of the floor making it even more resistant to damage from dirt. It is very important to use two buckets when cleaning the floor- one with the WOCA Wood Cleaner mixed solution and one with clean water for rinsing the dirty cloth or mop. Immerse the cloth or soft mop in the Soap solution, and then wring out the excess fluid before wiping the floor. Rinse the cloth or mop in the clear water, wring out the excess water, then immerse in the Soap solution again. Repeat this pattern until the floor is clean. Do not pour the Cleaner solution directly on the floor but instead, always use a cloth or mop to apply the solution.

Cleaning Extremely Dirty Floors

If the floor has been neglected and/or becomes very dirty, it should be cleaned using WOCA Lacquer Soap, mixed with water in a 40:1 ratio, following the guidelines above. Once this is dry you will then need to apply the WOCA Lacquer Care which strenghtens the lacquer, as it protects against wear and scratches and herby prolongs the lifetime of the lacquered surface. The Lacquer Care does not buid up a thick layer on the surface as the old layer is renewed with the next application.

Spot Remover

Difficult spots can be removed with WOCA Spot Remover. The Spot Remover is sprayed on the spot and left in place until the stain is dissolved, repeat treatment if necessary. The floor is then cleaned and with WOCA Lacquer Soap.

We recommend that you purchase a WOCA Lacquer Maintenance Kit with your floor.

Each kit contains

1.0 litre Woca Lacquer Soap (Will cover 350m2).
1.0 litre Woca Wood Cleaner (Will Cover 350m2)
1.0 litre Woca Lacquer Care (Will cover 60m2)
1 Polishing Pad and 1 Cloth.